Acquista per Marca
  • Acquista per Marca
  • Accusump by Canton
  • ADA
  • Advance Tapes
  • Aerocatch
  • AeroLoc
  • Alpinestars
  • Ampep
  • Anderson
  • AP Racing
  • Arai
  • AST Stop Watches
  • Aurora Rod End Bearings
  • Autoglym
  • Automec Brake Products
  • Avanti
  • AVO-TECHNICS
  • Bell
  • BG Racing
  • Bob Heath
  • Bosch
  • CamLoc
  • Carbon X
  • Cartek
  • Castle Combe Circuit
  • Castrol
  • Coast Fabrications
  • Cobra Seats
  • Cohline
  • Comex
  • Concept Racing
  • Cool It
  • Davies Craig
  • DMS
  • Dow Corning
  • Dunlop
  • Dzus
  • Eibach
  • Facet
  • Faulkner Springs
  • FK Rod Ends
  • FLURO Rod Ends
  • FSE
  • FuelX
  • Gates Vulcoflex
  • Girling
  • GKN
  • Go Pro
  • Gold Plug
  • Goodridge
  • Grayston
  • Grip Tyre Softener
  • Halo by Orthene
  • Hans
  • Hellerman
  • Hot Wire
  • Hunter
  • Hylomar
  • Indi
  • Intercomp
  • ITG
  • J-B Weld
  • Jetex
  • K-Seal
  • Laminova
  • Lifeline
  • Longacre
  • Lucas
  • Lumenition
  • Mann Filters
  • McLube Automotive
  • Mechanix
  • Merlin
  • Millers Oils
  • Mintex
  • Mobil 1 Oil
  • Mocal
  • Momo
  • Monit
  • Mountney
  • National
  • Newton Equipment
  • NGK Spark Plugs
  • NMB Bearings
  • Norma
  • OBP
  • Odyssey
  • Omex
  • OMP
  • P1 Racewear
  • Pagid Brake Pads
  • Peltor
  • Performance Braking
  • Pig
  • Piper
  • Polybush
  • Powervamp
  • Protech Shocks
  • PWR Oil Coolers
  • Racetech
  • Racewear Clearance
  • Rain-X
  • Recoil
  • Red Line
  • Revotec
  • Ringers
  • Samco
  • Schroth
  • Setrab
  • Sikaflex
  • Silkolene
  • Simpson
  • Smiths Gauges
  • SPA Technique
  • Sparco
  • Spax
  • Springalex
  • Stack
  • Stand 21
  • Stant
  • Stilo
  • SUSA
  • Sytec
  • Terratrip
  • Tex Mirrors
  • Thermo-Tec
  • Tickitape
  • Tilton
  • Tripac Fans
  • TRS
  • Valvoline
  • VDO
  • Vitaloni
  • VP Racing
  • Walbro
  • Walero
  • Webcon
  • Willans
  • Wilwood
  • Wipac
  • Zircotec
Back to Knowledge Base

I am running a Peugeot 205 GTI 1.6 in a BTRDA rally cross series. My exhaust noise level is 106db. New regs state that I must be below 100. If I fit this unit before my black box will it reduce the noise level to below 100db. I currently run straight from the manifold to the back box.

It is impossible to predict what the out come is going to be from fitting these inserts. Ideally if you have a bit of time before your event putting another silencer in to the system would be a better solution and less restrictive than the insert. It is quite a lot for a simple insert to take off though.

I would use the inserts and muffler add ons as last ditch attempts to get through a noise test rather than a permanent solution.

Archived in: Exhaust packing | Jetex exhausts

2nd June 2014

Does the above Q&A give you the answer you were looking for?